Hi all,

Here is log of ubuntu enterprise server on arndaleboard.
You look SATA, EHCI, USB ethernet working on arndaleboard.

We(me and other engineers) start to port main function include Framebuffer, HDMI, MFC, etc…).

Thanks.

log———-

U-Boot 2012.10-rc1-g61ec91e (Nov 14 2012 – 22:03:24) for ARNDALE5250

CPU: Exynos5250@1000MHz

Board: for ARNDALE5250
I2C: ready
DRAM: 2 GiB
WARNING: Caches not enabled
MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
*** Warning – bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: smc911x: Invalid chip endian 0xf3fff3ff
No ethernet found.
Hit any key to stop autoboot: 0
ARNDALE5250 #
ARNDALE5250 # dnw 40800000;dnw 41000000;dnw 43000000
prepare the dnw
OTG cable Connected!
Now, Waiting for DNW to transmit data
Checksum is being calculated…
Checksum O.K.
Download Done!! Download Address: 0×40800000, Download Filesize:0x24a640
prepare the dnw
OTG cable Connected!
Now, Waiting for DNW to transmit data
Checksum is being calculated…….
Checksum O.K.
Download Done!! Download Address: 0×41000000, Download Filesize:0x6186b5
prepare the dnw
OTG cable Connected!
Now, Waiting for DNW to transmit data
Checksum is being calculated.
Checksum O.K.
Download Done!! Download Address: 0×43000000, Download Filesize:0x2f41
ARNDALE5250 # bootm 40800000 41000000 43000000
## Booting kernel from Legacy Image at 40800000 …
Image Name: Linux-3.6.0-gf4c6664
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2401792 Bytes = 2.3 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum … OK
## Loading init Ramdisk from Legacy Image at 41000000 …
Image Name: Ramdisk
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6391413 Bytes = 6.1 MiB
Load Address: 41000000
Entry Point: 41000000
Verifying Checksum … OK
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0×43000000
Loading Kernel Image … OK
OK
Loading Ramdisk to 4f9e7000, end 4ffff675 … OK
Loading Device Tree to 4f9e1000, end 4f9e6f40 … OK

Starting kernel …

Uncompressing Linux… done, booting the kernel.
Booting Linux on physical CPU 0
Linux version 3.6.0-gf4c6664 (root@godori) (gcc version 4.4.6 (crosstool-NG 1.14.1) ) #3 SMP PREEMPT Sun Nov 18 21:20:58 KST 2012
CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Machine: SAMSUNG EXYNOS5 (Flattened Device Tree), model: SAMSUNG ARNDALE board based on EXYNOS5250
Truncating RAM at 60000000-6fffffff to -6f7fffff (vmalloc region overlap).
Ignoring RAM at 70000000-7fffffff (vmalloc region overlap).
Ignoring RAM at 80000000-8fffffff (vmalloc region overlap).
Ignoring RAM at 90000000-9fffffff (vmalloc region overlap).
Ignoring RAM at a0000000-afffffff (vmalloc region overlap).
Ignoring RAM at b0000000-bfffffff (vmalloc region overlap).
Memory policy: ECC disabled, Data cache writealloc
CPU EXYNOS5250 (id 0×43520010)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
EXYNOS5: PLL settings, A=1000000000, B=800000000, C=333000000
M=1600000000, E=96000000 V=300000000
EXYNOS5: ARMCLK=1000000000, CDREX=800000000, ACLK400=800000000
ACLK333=333000000, ACLK266=266666666, ACLK200=200000000
ACLK166=166500000, ACLK66=66666666
aclk_266_gscl: source is aclk_266 (1), rate is 266666666
sclk_g3d: source is mout_mpll_user (0), rate is 800000000
sclk_sata: source is mout_mpll_user (0), rate is 66666666
sclk_gscl_wrap: source is ext_xtal (0), rate is 24000000
sclk_gscl_wrap: source is ext_xtal (0), rate is 24000000
sclk_cam0: source is ext_xtal (0), rate is 24000000
sclk_cam1: source is ext_xtal (0), rate is 24000000
PERCPU: Embedded 7 pages/cpu @c0ac7000 s6400 r8192 d14080 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 193040
Kernel command line: root=/dev/ram0 rw console=ttySAC2,115200
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 760MB = 760MB total
Memory: 760108k/760108k available, 18132k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 – 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 – 0xfffe0000 ( 896 kB)
vmalloc : 0xf0000000 – 0xff000000 ( 240 MB)
lowmem : 0xc0000000 – 0xef800000 ( 760 MB)
modules : 0xbf000000 – 0xc0000000 ( 16 MB)
.text : 0xc0008000 – 0xc041b0a4 (4173 kB)
.init : 0xc041c000 – 0xc0442900 ( 155 kB)
.data : 0xc0444000 – 0xc0483d80 ( 256 kB)
.bss : 0xc0483da4 – 0xc04b9234 ( 214 kB)
SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:549
sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
Console: colour dummy device 80×30
Calibrating delay loop… 1987.37 BogoMIPS (lpj=9936896)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x403201f0 – 0×40320248
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (3981.31 BogoMIPS).
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
S3C Power Management, Copyright 2004 Simtec Electronics
EXYNOS5250 PMU Initialize
EXYNOS: Initializing architecture
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
IN the i2c probe *********************
s3c-i2c sata-phy-i2c: slave address 0×38
s3c-i2c sata-phy-i2c: bus frequency set to 39 KHz
s3c-i2c sata-phy-i2c: i2c-0: S3C I2C adapter
- 받은메일 표시 -
ahci-sata sata_exynos: forcing PORTS_IMPL to 0×1
ahci-sata sata_exynos: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0×1 impl platform mode
ahci-sata sata_exynos: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0×100 irq 147
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver cdc_ncm
ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
s5p-ehci s5p-ehci: S5P EHCI Host Controller
s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
s5p-ehci s5p-ehci: irq 103, io mem 0×12110000
s5p-ehci s5p-ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S5P EHCI Host Controller
usb usb1: Manufacturer: Linux 3.6.0-gf4c6664 ehci_hcd
usb usb1: SerialNumber: s5p-ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
exynos-ohci exynos-ohci: Already power on PHY
exynos-ohci exynos-ohci: EXYNOS OHCI Host Controller
exynos-ohci exynos-ohci: new USB bus registered, assigned bus number 2
exynos-ohci exynos-ohci: irq 103, io mem 0×12120000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EXYNOS OHCI Host Controller
usb usb2: Manufacturer: Linux 3.6.0-gf4c6664 ohci_hcd
usb usb2: SerialNumber: exynos-ohci
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
mousedev: PS/2 mouse device common for all mice
Synopsys Designware Multimedia Card Interface Driver
dwmmc_exynos dw_mmc.0: Using internal DMA controller.
dwmmc_exynos dw_mmc.0: DW MMC controller at irq 107, 32 bit host data width, 128 deep fifo
dwmmc_exynos dw_mmc.0: wp gpio not available
dwmmc_exynos dw_mmc.0: 1 slots initialized
dwmmc_exynos dw_mmc.0: Version ID is 241a
dwmmc_exynos dw_mmc.2: Using internal DMA controller.
mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
dwmmc_exynos dw_mmc.2: DW MMC controller at irq 109, 32 bit host data width, 128 deep fifo
dwmmc_exynos dw_mmc.2: wp gpio not available
dwmmc_exynos dw_mmc.2: 1 slots initialized
dwmmc_exynos dw_mmc.2: Version ID is 241a
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
mmc0: BKOPS_EN bit is not set
mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
mmc0: new high speed DDR MMC card at address 0001
mmcblk0: mmc0:0001 M4G1FA 3.72 GiB
TCP: cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
mmcblk0boot0: mmc0:0001 M4G1FA partition 1 1.00 MiB
Registering SWP/SWPB emulation handler
mmcblk0boot1: mmc0:0001 M4G1FA partition 2 1.00 MiB
mmcblk0: p1 p2 p3 p4
mmcblk0boot1: unknown partition table
mmcblk0boot0: unknown partition table
mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
usb 1-3: new high-speed USB device number 2 using s5p-ehci
mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 50000000Hz, actual 50000000HZ div = 1)
mmc1: new high speed SDHC card at address b368
mmcblk1: mmc1:b368 NCard 3.70 GiB
mmcblk1: p1
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
usb 1-3: New USB device found, idVendor=0424, idProduct=3503
usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 3 ports detected
ata1.00: ATA-8: Comay Venus Pro 3, 2.52, max UDMA/133
ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA Comay Venus Pro 2.52 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
RAMDISK: gzip image found at block 0
usb 1-3.2: new high-speed USB device number 3 using s5p-ehci
usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610
usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-3.2: Product: USB2.0 Hub
hub 1-3.2:1.0: USB hub found
hub 1-3.2:1.0: 4 ports detected
usb 1-3.2.4: new high-speed USB device number 4 using s5p-ehci
usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a
usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-3.2.4: Product: AX88772
usb 1-3.2.4: Manufacturer: ASIX Elec. Corp.
usb 1-3.2.4: SerialNumber: 000001
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing init memory: 152K
INIT: version 2.84 booting
asix 1-3.2.4:1.0 eth0: register ‘asix’ at usb-s5p-ehci-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 00:00:00:00:00:00
INIT: Entering runlevel: 3

Linux 2.6.35.7-Origen(by InSignal Co., Ltd.)

/) /)
(=’.'=)

login[1105]: root login on ‘ttySAC2′
ls: /dev/ttyF*: No such file or directory
root@godori:~#
root@godori:~#
root@godori:~#
root@godori:~# dir
-sh: dir: not found
root@godori:~# ls -l
total 0
root@godori:~# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

lo Link encap:Local Loopback
LOOPBACK MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

root@godori:~# 00:01:3f:00:00:01
root@godori:~#
root@godori:~#
root@godori:~#
root@godori:~# ifconfig eth0 hw ether 00:01:3f:00:00:01
root@godori:~# ifconfig eth0 192.168.0.102 up
root@godori:~# asix 1-3.2.4:1.0 eth0: link down
asix 1-3.2.4:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1

root@godori:~#
root@godori:~#
root@godori:~# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:01:3F:00:00:01
inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:665 (665.0 B) TX bytes:0 (0.0 B)

lo Link encap:Local Loopback
LOOPBACK MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

root@godori:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:01:3F:00:00:01
inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:665 (665.0 B) TX bytes:0 (0.0 B)

root@godori:~# route add default gw 192.168.0.1 eth0
root@godori:~#
root@godori:~#
root@godori:~# ping 192.168.0.1
PING 192.168.0.1 (192.168.0.1): 56 data bytes
64 bytes from 192.168.0.1: seq=0 ttl=64 time=3.255 ms
64 bytes from 192.168.0.1: seq=1 ttl=64 time=13.752 ms
64 bytes from 192.168.0.1: seq=2 ttl=64 time=0.672 ms
64 bytes from 192.168.0.1: seq=3 ttl=64 time=0.734 ms
64 bytes from 192.168.0.1: seq=4 ttl=64 time=0.663 ms
64 bytes from 192.168.0.1: seq=5 ttl=64 time=0.726 ms
64 bytes from 192.168.0.1: seq=6 ttl=64 time=0.656 ms
64 bytes from 192.168.0.1: seq=7 ttl=64 time=0.719 ms
64 bytes from 192.168.0.1: seq=8 ttl=64 time=0.655 ms

— 192.168.0.1 ping statistics —
9 packets transmitted, 9 packets received, 0% packet loss
round-trip min/avg/max = 0.655/2.425/13.752 ms
root@godori:~#